7 · Network Forensics

← Collectors · Home · Next: Reports & Schemas →

Live capture and offline analysis. Capture and parse only. The crate opens capture handles and reads savefiles; it never transmits. No injection, no ARP or DNS spoofing, no interception. The capture library’s send path is never called — out of scope by design, not by omission.

Contents

• Live capture
• BPF filters
• Drops
• Stopping cleanly
• Offline analysis
• Link types
• Flows
• TCP reassembly
• Indicators
• Windows and Npcap
• Limitations

Live capture

sudo arachnid-core capture -o ./ev-net -d eth0 -f "tcp port 443" --duration 300

Needs root or CAP_NET_RAW on Linux, Npcap driver access on Windows.

How the capture loop works

The handle is opened with:

• snaplen 65535 by default — full frames, because a truncated payload is a truncated indicator;
• promiscuous off by default;
• read timeout 250 ms and immediate mode, then set to non-blocking.

The bounded timeout is why Ctrl-C works on an idle link: without it the loop would block in the driver until the next packet arrived. On no-packet returns it sleeps 20 ms rather than spinning.

Each iteration checks, in order: the stop flag, the packet limit, the duration — then reads one packet, writes it to the savefile, and updates the counters.

stop_reason in the output records which one fired: interrupted by operator, packet limit reached, or duration elapsed.

Counters, not packets

A front end gets running totals — packets and bytes — through plain atomics, not a channel of decoded packets.

The capture loop must not do per-packet work on behalf of a UI. Falling behind the link drops evidence. Counters are the most a display can be given for free; packet detail comes from re-reading the savefile once it is closed and sealed.

That is why the TUI’s live capture screen shows numbers, and the flow breakdown only appears after the capture stops.

BPF filters

-f/--filter takes standard pcap-filter syntax, the same language tcpdump uses.

-f "tcp port 443"
-f "tcp port 443 and not host 10.0.0.1"
-f "not port 22"                       # exclude your own SSH session
-f "host 192.0.2.10 or host 192.0.2.11"
-f "net 10.0.0.0/8 and not net 10.1.0.0/16"
-f "udp port 53"                       # DNS only
-f "tcp[tcpflags] & tcp-syn != 0"      # SYNs

Filters are compiled and applied in the kernel. Excluded traffic is never copied into userspace: not in the savefile, not in RAM, not in scope. That matters when the exclusion is legally required rather than merely convenient — you can state that the traffic was never collected, not merely discarded.

An invalid filter fails at open time with the filter text in the error:

error: apply BPF filter "tcp portt 443": syntax error

The same syntax applies to parse-pcap -f, where it is applied while reading the savefile.

Excluding your own session

Always worth doing. Your SSH or RDP session to the host is not evidence, and it is noisy:

sudo arachnid-core capture -o ./ev-net -d eth0 -f "not port 22" --duration 600

Drops are a finding

- ⚠ **Dropped 1204 (kernel) / 0 (interface) — this capture has gaps.**

Two counters, from pcap_stats:

Non-zero on either sets exit code 4, emits a WARN line, and adds a custody note:

capture dropped 1204 kernel / 0 interface packets; evidence has gaps

A capture with drops has holes in it, and holes in evidence must be visible. Never present a lossy capture as a complete record of the traffic.

Remedies, in order of effectiveness:

1. Tighten the BPF filter. Kernel-side filtering is free; everything else is not.
2. Lower --snaplen. 1500 or even 256 is plenty if you only need headers and indicators — but it truncates payloads, so reassembly and HTTP/TLS parsing suffer.
3. Capture to faster storage. A USB stick is a common culprit.
4. Capture for shorter windows, repeatedly.

Stopping cleanly

Ctrl-C sets a flag; it does not kill the process. The loop notices, exits, and then:

1. flushes the savefile,
2. closes it,
3. reads pcap_stats for the drop counters,
4. hashes the file and seals it into the custody log,
5. writes the report.

Losing a capture to an abrupt exit would be losing evidence. The same applies in the TUI: quitting mid-capture asks for confirmation, and confirming sets the stop flag rather than dropping the thread.

If the capture library returns a hard error mid-run, the savefile is still flushed before the error propagates — you keep what was captured up to that point.

Offline analysis

arachnid-core parse-pcap capture.pcap -o ./ev-pcap

Reads a PCAP or PCAPNG read-only. The file stays where it is; it is not copied into the container. Its SHA-256 is recorded in the custody log, binding the analysis to the exact bytes analysed:

source pcap capture.pcap sha256=ce51b95b…7f6e02 size=454

Output goes to artifacts/pcap_analysis.json:

{
  "schema_version": "1.0.0",
  "source": "sample.pcap",
  "source_sha256": "ce51b95bad82ae3fa035ff637cd43145df75a9fd2ce82037a6e0d4754a7f6e02",
  "datalink": "Linktype(1)",
  "packets": 3,
  "bytes": 382,
  "decode_errors": 0,
  "first_packet_utc": "2026-01-01T00:00:00Z",
  "last_packet_utc": "2026-01-01T00:00:02Z",
  "flows": [ … ],
  "indicators": [ … ]
}

Decode errors

decode_errors counts frames the decoder could not parse: malformed, truncated by snaplen, or a link type this build does not handle. Non-zero sets exit code 4 and is reported.

Non-IP frames are not errors. ARP, LLDP and friends are counted in packets and bytes but contribute no flow and no error — they simply are not flows.

Link types

The link-layer header is stripped before decoding. A link type this build does not decode returns nothing, so the frame is counted as a decode error rather than misparsed into a phantom flow.

For raw-IP link types there is no Ethernet header, so the first nibble is version-sniffed (4 or 6) to decide how to slice the packet.

Capturing on the Linux any pseudo-device gives you linktype 113, which is supported — useful when you do not know which interface the traffic will use.

Flows

One transport-layer conversation, keyed by the 5-tuple as first observed:

{
  "protocol": "tcp",
  "src_addr": "192.168.1.50",
  "src_port": 44102,
  "dst_addr": "93.184.216.34",
  "dst_port": 80,
  "packets": 1,
  "bytes": 159,
  "first_seen_utc": "2026-01-01T00:00:02Z",
  "last_seen_utc": "2026-01-01T00:00:02Z",
  "reassembled_bytes": 105,
  "truncated": false
}

• Keyed directionally: A→B and B→A are separate flows. That is deliberate — reassembly is per-direction, and so are the indicators drawn from it.
• bytes counts captured bytes (caplen), so a low --snaplen shows up here.
• reassembled_bytes is payload recovered by reassembly. TCP only; zero for UDP.
• truncated means the flow hit the reassembly ceiling.
• Sorted by bytes descending, then source address.

TCP reassembly

Segments arrive out of order and get retransmitted, so payload is keyed by sequence offset in a BTreeMap rather than appended in arrival order. That:

• sorts the stream correctly regardless of arrival order,
• collapses duplicate retransmissions,
• makes a gap visible instead of silently splicing two non-adjacent regions together.

Signed offsets

Offsets are signed deltas from the first sequence number seen. The first segment captured is not necessarily the lowest one — a reordered network, or a capture that starts mid-stream, both break that assumption. A segment preceding the base gets a negative offset and still sorts into place.

Signed 32-bit arithmetic is also what makes sequence wraparound a non-event, on the standard TCP assumption that a live window spans well under 2 GiB.

Retransmissions

A retransmission of an already-stored offset is dropped, unless it carries more data than what is already held — in which case it replaces it. That handles the overlapping-segment case without letting a later segment silently rewrite earlier bytes.

The ceiling

--max-stream-bytes <BYTES>    default 8388608 (8 MiB)

A capture holding a multi-gigabyte download must not put that download in RAM. When a flow hits the ceiling:

• storage stops,
• truncated is set to true on that flow,
• the flow is never silently shortened — the flag is the contract.

Indicators live in the first few KiB of a stream, so a lower ceiling rarely costs you one. Raise it when you need more of a payload reconstructed; lower it when memory is tight:

arachnid-core parse-pcap big.pcap -o ./ev --max-stream-bytes 2097152

# how many flows were cut short?
jq '[.flows[] | select(.truncated)] | length' ./ev/artifacts/pcap_analysis.json

Indicators

Everything here is derived from bytes that were actually captured.

Nothing is resolved, enriched, or looked up against any remote service. A triage tool that phones out about the indicators it found leaks the investigation.

Indicators are deduplicated by (kind, value) and carry a count and a first/last-seen window:

{
  "kind": "http_host",
  "value": "c2.example.net",
  "count": 1,
  "first_seen_utc": "2026-01-01T00:00:02Z",
  "last_seen_utc": "2026-01-01T00:00:02Z",
  "context": "192.168.1.50:44102 -> 93.184.216.34:80"
}

Sorted by kind, then count descending, then value.

The kinds

DNS parsing

Names are decoded with compression pointers followed, and the walk is bounded (128 steps) because a malicious or corrupt message can point in a cycle. Question and answer sections are each capped at 64 entries.

DNS over TCP is length-prefixed; the parser skips the two-byte length before reading the message.

Answer types decoded: A (type 1), AAAA (type 28), CNAME (type 5). Others are skipped rather than guessed at.

TLS SNI

Reassembly runs first, so a ClientHello split across segments still parses. The parser walks: TLS record header → handshake header → version → random → session id → cipher suites → compression methods → extensions, then finds extension type 0x0000 (server_name) and reads the first name.

Encrypted ClientHello yields no SNI, and neither does a TLS 1.3 handshake that omits it. Arachnid reads the plaintext handshake and does not attempt to decrypt anything. That is a limitation, not a bug: a triage tool that decrypted traffic would need keys it has no business holding.

HTTP parsing

Deliberately line-based rather than a full HTTP parser. A reassembled stream can hold several pipelined requests and a truncated tail; a strict parser would reject the whole thing.

• Methods recognised: GET, POST, PUT, HEAD, DELETE, OPTIONS, PATCH, TRACE, CONNECT.
• A request line must also contain HTTP/1. to count, which keeps a payload that merely starts with GET from being read as a request.
• Only Host: and User-Agent: headers are extracted — the two worth pivoting on.
• The scan is bounded to the first 64 KiB of a stream. Indicators live in the headers, not in an 8 MiB body.
• Header names are matched case-insensitively.

HTTP/2 and HTTP/3 are not parsed. Both are binary and usually inside TLS; you get the tls_sni instead.

Pivoting on indicators

# every hostname seen, whatever the source
jq -r '.indicators[]
       | select(.kind | test("dns_query|tls_sni|http_host"))
       | .value' ev-pcap/artifacts/pcap_analysis.json | sort -u

# the top talkers
jq -r '.indicators[] | select(.kind=="ipv4") | "\(.count)\t\(.value)"' \
   ev-pcap/artifacts/pcap_analysis.json | sort -rn | head -20

# DNS answers, resolved names to addresses
jq -r '.indicators[] | select(.kind=="dns_answer") | .value' \
   ev-pcap/artifacts/pcap_analysis.json

Windows and Npcap

wpcap.dll is the user-mode half of the Npcap kernel driver, and it cannot be statically linked by anyone. Arachnid handles this carefully:

Delay-loading. The pcap crate declares wpcap.dll as a normal import, which means the process could not even start without Npcap — so verify, report and collect would all fail with STATUS_DLL_NOT_FOUND on a host with no packet driver, which describes most analyst workstations. The release build passes /DELAYLOAD:wpcap.dll, deferring resolution to the first pcap call.

Search path. Npcap installs to %SystemRoot%\System32\Npcap, which is deliberately not on the default DLL search path. Arachnid prepends it to PATH once, before any capture thread exists.

A readable error instead of an abort. Calling into pcap without the DLL would abort the process through the delay-load handler, which is not a Rust error anyone can catch. So every entry point that touches pcap calls ensure_pcap_available() first:

error: Npcap is not installed, or wpcap.dll is not on the DLL search path.
       Packet capture and PCAP parsing need it; install Npcap from https://npcap.com/.
       Every other subcommand (collect, verify, report) runs without it.

CI deliberately installs only the Npcap SDK and not the runtime, so the no-Npcap path is tested on every push.

On Unix, libpcap is an ordinary shared-library dependency resolved at load time, so there is nothing to check and ensure_pcap_available() is a no-op.

Limitations

← Collectors · Home · Next: Reports & Schemas →